HistoCore SPECTRA CV RFID-Registration Registro de RFID Registro RFID تسجيل التعريف عن طريق الترددات الالسلكية Version 1.1, Revision B 08.2018 RFID-Registration HistoCore SPECTRA CV Order No.: 14 0514 89998 Revision B Always keep this manual with the instrument. Read carefully before working with the instrument.
Table of contents Registro de RFID para Argentina... 4 RFID-Registration for Australia and New Zealand... 4 Registro RFID para México... 4 RFID-Registration for Singapore... 5... 5 RFID-Registration for the United States of America and Canada... 6 For HistoCore SPECTRA CV 3
RFID-Registration HistoCore SPECTRA ST Registro de RFID para Argentina Símbolo en la etiqueta de identificación: Título del símbolo: Descripción: Marca de homologación de CNC Una identificación CNC asignada por la Comisión Nacional de Comunicaciones para identificar los productos de radio en el mercado argentino. El número de certificación consta de lo siguiente: CNC = H = Comisión Nacional de Comunicaciones Número de registro asignado por la CNC al equipo 21511 = Número de registro asignado por la CNC al equipo RFID-Registration for Australia and New Zealand Symbol on the Identification Label: Title of Symbol: Description: Registro RFID para México RCM/R-NZ Compliance Mark The Regulatory Compliance Mark (RCM) indicates a device's compliance with applicable ACMA technical standards of New Zealand and Australia that is, for telecommunications, radio communications, EMC and EME. The R-NZ mark is the compliance mark for radio transmitting products (see the Radiocommunications (Radio Standards) Notice). As there may be different radio frequency allocations in New Zealand and Australia the New Zealand radio label, R-NZ, indicates compliance to New Zealand standards only. Símbolo en la etiqueta de identificación: Título del símbolo: Descripción: Marca de conformidad del IFETEL La marca de conformidad del Instituto Federal de Telecomunicaciones (IFETEL) es un requisito que deben cumplir los equipamientos de telecomunicación en relación a los estándares y especificaciones provistos para México. 4 RFID-Registration 1.1 Rev B 08.2018
RFID-Registration HistoCore SPECTRA ST RFID-Registration for Singapore Symbol on the Identification Label: Title of Symbol: Description: IMDA compliance mark The Info-communications Media Development Authority (IMDA) compliance mark is a requirement for telecommunication equipment to comply with applicable standards and specifications for Singapore. For HistoCore SPECTRA CV 5
RFID-Registration HistoCore SPECTRA ST RFID-Registration for the United States of America and Canada Symbol on the Identification Label: FCC ID: 2AAPD-SPECTRACV01 IC: 12028A-SPECTRACV01 Title of Symbol: FCC-Approved Equipment Description: This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Changes or modifications made to this equipment not expressly approved by Leica Biosystems Nussloch GmbH may void the FCC authorization to operate this equipment. 6 RFID-Registration 1.1 Rev B 08.2018
www.leicabiosystems.com Version 1.1, Revision B 08.2018 Leica Biosystems Nussloch GmbH Heidelberger Str. 17-19 D-69226 Nussloch Germany Tel.: +49 - (0) 6224-143 0 Fax: +49 - (0) 6224-143 268 Web: www.leicabiosystems.com